The most common mistake after putting 33s on a Colorado is blaming the transmission. The automatic hunts between gears on every grade, the cruise control surges, the speedometer reads slow, and the owner assumes something is wrong with the tune. Usually nothing is broken. The tires are simply taller than the axle gearing was designed for. The short answer to "do I need to regear my Chevy Colorado" is this: a tire an inch or so taller than stock rarely needs new gears, 31 to 32 inches is the gray area where it depends on your engine and load, and 33 inches or more on a stock ratio is where most owners start to feel it.
This guide covers the math for your own truck, the symptoms that point at gearing, how to choose a ratio, and what to do after the swap so the new gears last.

What gear ratio does on a Colorado
The ring and pinion in each axle multiplies engine torque before it reaches the tires. A numerically higher ratio, such as 3.73 compared with 3.42, multiplies more torque and spins the engine faster at a given road speed. A taller tire does the opposite: it makes the whole drivetrain act as if it had a numerically lower ratio. Add big tires without touching the gears and you have handed the truck a tall, lazy final drive.
The Colorado is a midsize pickup, which makes it more sensitive to this than a heavy-duty truck. It has independent front suspension with a frame-mounted front differential, a solid rear axle on leaf springs, and a range of engines, from a four-cylinder to a V6, a turbo four, or a diesel depending on the generation. A torquey diesel or turbo engine hides a tall ratio better than a naturally aspirated one that needs revs to make power, so the same tire can feel fine on one Colorado and sluggish on another. The ZR2 and some other trims also ship with factory lockers and different tire packages, which affects both the starting ratio and what parts fit.
Ratios differ by engine, axle, and package, so do not trust a forum post. Check the RPO label (usually in the glovebox) or have a parts counter look it up by VIN, and write the number down. Every calculation below starts with it.
How to calculate the ratio you need
This takes two minutes with a calculator. The goal is to keep the effective ratio close to what the truck had from the factory.
- Find the diameter of your stock tires. Measure it, or look up the exact size printed on the sidewall.
- Find the diameter of the new tire. A 265/70R17 is about 31 inches, a 285/70R17 is about 33 inches, and a 315/70R17 is about 35 inches.
- Divide the new diameter by the old diameter.
- Multiply your factory ratio by that number. The result is the ratio that restores factory behavior.
Here is a worked example with round numbers. A Colorado with a 3.42 ratio on 29-inch tires moving to 33-inch tires is a 14 percent change, so the matching ratio is about 3.90. Gear sets come in fixed sizes, so you round to the nearest available option, and what is offered for your axle depends on the supplier and generation. Check availability before you commit to a tire size.
If you are still choosing a tire, the Chevy Colorado tire size guide covers what fits at each lift height, and Regearing After Bigger Tires covers the general case for any truck.

Symptoms that mean your gearing is wrong
Gearing problems show up as behavior, not warning lights. Watch for these after a tire change:
- Constant shifting on grades. The transmission cannot hold a gear on a moderate hill and hunts between two gears.
- Slow, flat acceleration. The truck feels heavy off the line and takes a long time to build speed with passengers and gear aboard.
- Poor towing and loaded performance. Anything heavy in the bed or on the hitch exposes the problem fast.
- Worse fuel economy than before. The engine works harder and downshifts more often, so mileage drops even though it turns slower on the highway.
- A speedometer that reads low. This is a calibration issue as much as a gearing one, and it is separate from how the truck drives.
- Weak engine braking on descents. A tall ratio gives you less help holding speed downhill.
If you only see a couple of these and mostly drive flat highway, you may be fine with a lighter foot. If you see most of them, regearing is the real fix. A tune can help at the margin, but it cannot restore the leverage the tire took away.
Which tire sizes usually need regearing
Use these as a starting point, then adjust for your engine, transmission, and how much weight you carry.
- Up to roughly 31 inches: usually fine on stock gears, and many trims come close to this from the factory.
- 32 to 33 inches: a judgment call. An empty Colorado on pavement often copes. One that carries a bed rack, a canopy, a bumper and winch, and a full camping load will feel it sooner.
- 34 to 35 inches: plan on regearing. On a midsize truck, skipping it is the most common regret after a lift and tire build.
Weight matters as much as diameter. A loaded overland Colorado behaves like a heavier truck on a bigger tire even when the tire is modest, because the engine has more mass to move. Size your decision to the truck you actually drive, not the empty one. The Chevy Colorado lift kit guide covers how much room each lift height gives you.

Engine, transmission, and altitude change the answer
Two owners with the same 33-inch tire can report opposite results, and the reasons are usually practical. A diesel or turbo engine with a wide torque band hides a tall ratio better than a V6 that needs revs. A truck that lives at altitude loses power in thin air and feels a tall ratio much more, which is why mountain owners tend to regear sooner. Newer trucks with more transmission gears can mask the problem on flat roads, then hunt noticeably on a long climb with a load.
One free test tells you a lot. Drive a familiar hill at highway speed with the cruise control on and note whether the transmission holds one gear or keeps dropping out of it. Do it empty and again loaded. If it hunts only when loaded, you have a margin problem rather than a broken truck, and a ratio change is the clean fix.
Choosing a ratio and what the swap involves
Pick the numerically higher ratio when you are between two options and you tow, carry weight, or drive in the mountains. Pick the lower one if most of your miles are highway and you want a quiet engine. Either way, a few rules do not change:
- Front and rear must match. Both axles need the same ratio. A mismatch binds the driveline and can damage the transfer case.
- Check for factory lockers first. If your Colorado has a rear locker or a front locker, confirm the new gear set and carrier are compatible before you order. For how lockers work, see Lockers vs. Limited Slip vs. Open.
- Do it as a complete job. Gears, bearings, seals, and fluid are replaced together, and the setup is measured and adjusted rather than guessed.
- Use a shop that sets up gears every week. Pattern and backlash setup is skilled work, and a poor job is loud and short-lived.
- Ask about warranty first. Drivetrain changes on a newer truck can affect coverage, so ask your dealer before you start.
Browse gearing for ring and pinion sets and install hardware.

After the swap: break-in, calibration, and fluid
New gears need gentle treatment for the first several hundred miles. Drive normally, avoid heavy towing and hard launches, and let the fluid heat up and cool down a few times. Most shops recommend an early fluid change after break-in because fine metal from the new gears ends up in the oil.
Then fix the speedometer. Tire diameter and gear ratio both change the reading, so a regear alone does not make it correct. Recalibrate with a programmer or at a shop, and check against a GPS reading on the highway. Traction control, ABS, and the driver-assist systems all read wheel speed, so confirm they behave normally on a wet road.
Finally, keep up the maintenance. Axle fluid should be changed on a schedule and any time the housing has been underwater, which Water in Your Axles explains. If fuel economy is a concern after the build, Offroad Fuel Economy After Mods shows what to expect and what really helps. And if you are unsure how your transfer case ranges work with the new gearing, 4H vs 4L vs AWD is a good refresher.

Common regearing mistakes on Colorados
- Regearing for the tire you might buy later. Choose the ratio for the tire you actually run now.
- Changing only one axle. Front and rear have to match.
- Ignoring the speedometer. Calibrate it, or every mile, trip, and fuel calculation will be wrong.
- Forgetting the weight you carry. A canopy, bumper, and camping gear change the answer more than a quarter inch of tire.
- Buying the cheapest gear set. Gear quality shows up in noise and lifespan.
Frequently asked questions
Do I need to regear my Colorado for 33-inch tires?
Often yes, more so than on a bigger truck. If the transmission holds gear on hills and tows without hunting, you can wait. If it constantly downshifts and feels slow with your normal gear aboard, regearing will fix it.
What gear ratio is best for 33-inch tires on a Colorado?
It depends on your factory ratio, tire diameter, and how much weight the truck carries. Do the division from your own stock ratio, then pick the nearest available set.
Can I regear just the rear axle?
No. Front and rear must carry the same ratio, or the axles fight each other and stress the transfer case.
Will regearing improve my gas mileage?
It can, by keeping the engine in a better range and reducing hunting between gears. Do not expect it to beat the mileage of the stock tire, but it often recovers part of what big tires took away.
Where to go from here
Write down your factory ratio, measure your tire, and do the division before you spend money. When you are ready, browse gearing for ring and pinion sets, check all wheels and tires if you are still picking a size, and see suspension components if the new tires need more room.
Related reading
- Regearing After Bigger Tires — the general explainer behind the math.
- Chevy Colorado Tire Size Guide — what fits at each lift height.
- Ford Bronco Regear Guide — the same walkthrough for the Bronco.
